Are Driveshafts Universal?

On a typical four-wheel drive or all-wheel drive vehicle, there are two driveshafts. There is the same driveshaft that is on a rear-wheel drive car but there is also an additional front driveshaft that is connected to the front differential and the transfer case by u-joints.

Are driveshafts interchangeable?

Yes, the driveshaft will be different per body style and box length, also engine/trans plays a factor as well. Going from 2500 -> 1500 wouldn’t be good; u-joint at the rear axle will be different size. You might be able to find a similar ext. cab 3500, that might fit.

Does drive shaft diameter matter?

Length And DiameterOther than balance, the length and diameter of the driveshaft directly affect the performance of the unit. Critical speed is the rpm at which the driveshaft becomes unstable and begins to bend into an S shape. The longer and smaller (diameter) a driveshaft is, the lower its critical speed.

What is the strongest driveshaft?

There are three factors that make a driveshaft strong; material, diameter, and u-joint size. In terms of material, steel and thicker walls will be the strongest choice, though there are obvious drawbacks with the added weight.

What is a 1310 driveshaft?

The 1310 series joint is what you would expect to find stock in most Jeep or small trucks. A 1350 series joint/shaft is what you might find in many full size trucks. While it’s not 100% accurate, you could say that a 1310 is a “half ton” joint and a 1350 is a “one ton joint”.

Are Subaru driveshafts interchangeable?

they’re usually all the same within generations if you just match the automatic/manual part of the equation – everything else is the same on driveshafts, Subaru doesn’t change much.

How much does it cost to balance a driveshaft?

From what we researched via multiple quotes online, the average driveshaft balancing, including professional labor, tends to be in the $120 to $185. However, if you needed new U-joints, as well as the driveshaft balancing, which is often the case in most repairs, the price can be closer to $200 to $250+.

How much does it cost to replace a driveshaft?

Driveshaft Replacement Cost

On average, you can expect to pay anywhere from $400 to $1,260 total but it can easily approach close to $2,000 for some vehicles. If you have a four-wheel drive vehicle, you may have two driveshafts but in most cases, only one will need to be replaced.

What happens if my drive shaft breaks while driving?

A broken driveshaft can prevent wheels from turning properly, giving you trouble when trying to make turns. This issue limits your overall control of the car. You need any issues that prevent you from driving the car correctly addressed right away for safe driving and continued use of the vehicle.

What happens when u-joint fails?

What Happens When a U-Joint Fails? When a u-joint fails, your vehicle breaks down and stops moving. … There may also be extensive damage to the underside of the vehicle and potentially to the driveline itself. The u-joint is a small part, but it can cause thousands of dollars in repairs if it completely fails.

When two driveshaft yokes are in alignment with each other they are considered?

C) in phase. When two drive shaft yokes are in alignment with each other, they are considered: A) in harmony.

How much does it cost to fix u-joints?

The average price for the u joint replacement cost ranges between $190 and $260 for the replacement, while the labor on this job runs between $170 and $210 on aveage, with the parts ranging between $20 and $50. Keep in mind, the average u joint replacement cost will vary depending on the type of vehicle you have.

How is a driveshaft balanced?

To field balance a driveshaft, raise vehicle parallel to the ground so that the vehicle can be started and the tires and wheels can rotate freely. Measure about six inches from the yoke end, and place four marks 90 degrees apart around the driveshaft. Number them so that they can be identified.

How much power can a 1310 u-joint handle?

While the 1310 series, the stock size for most Jeeps, is rated for 1,600 lb-ft of torque.”

What is the difference between 1330 and 1350 u-joint?

Take note that the u-joint is only as strong as the smallest series number. The 1330 to 1350 U Joint cross width is 3.625 (3 5/8”) on both sides, while the cap diameters are different. 1 1/16″ on the 1330 side and 1 3/16″ on the 1350 side.

What size u-joint do I need?

For most cars, 1310-series U-joints are typical choice, but for performance applications, the rugged 1350-series joints are the better choice. The larger the series number, the larger the trunnion. Trunnions are the protruding shafts that the caps ride over. Larger trunnions equate to more torsional strength.

What’s better steel or aluminum driveshaft?

An aluminum racing driveshaft is going to be more expensive than a steel one and carbon-fiber is going to be more expensive than that. … “The steel can take a lot more abuse than any of the other shafts, but the aluminum and carbon-fiber shafts are also a lot lighter weight and as a result take less torque to rotate.

Does a carbon-fiber driveshaft make a difference?

In our case (see pix) it would have been more cost effective at first to get the more expensive and stronger QA1 carbon-fiber driveshaft. Sure, a quality carbon-fiber shaft is more costly, but it offers better strength, high-speed dynamics, and obviously less rotational weight for quicker acceleration.

How do I choose a drive shaft?

There are many factors to be considered when selecting a driveshaft. They include the type of shaft material, diameter, thickness and length, yokes, and U-joints that are properly rated for the task at hand.

Can you install a driveshaft wrong?

If they split the shaft and not re install it correctly, they will throw the shaft out of balance and cause an uncomfortable vibration. One piece shaft guys have the slip yoke in the t-case, so they dont have to worry about any of this.

How do you tell if u-joint is bad?

Symptoms of a Bad or Failing Universal Joint (U-Joint)

  1. Squeaking noise when starting to move (forward or reverse) …
  2. “Clunk” with a ringing sound when shifting from Drive to Reverse. …
  3. Vibration felt throughout the vehicle while moving forward at speed. …
  4. Transmission fluid leaks from the rear of the transmission.

What does a driveshaft vibration feel like?

A common symptom of a failing driveshaft is an intense shaking coming from underneath the vehicle. Worn out u-joints or bushings can cause the driveshaft to vibrate. … Vibrations caused by tire balance issues are speed sensitive while driveshaft vibrations aren’t.

How long can I drive on a bad u-joint?

A car with a bad U-joint will break down in a few hundred miles at the maximum. But if you have a bad U-joint and you are having a transmission fluid leakage, you should not drive your car since the U-joint may break down anytime and will cause damage to the brake line, drive shaft, transmission line and other parts.