What is a pre send? A pre aux send delivers the signal out of the mixer BEFORE it passes through the channel fader; pre-fader. Therefore, you can move the volume fader all you want but it’s not going to affect the volume going to that auxiliary unit.
What is pre fader level?
In pre fader mode, your meters show the signal level after the inserts. It is not affected by the fader level. Therefore, the fader could be at negative infinity dBFS but the channel will still show the signal after the last insert. In post fader metering, you meter is affected by your fader level as well.
What is Pre-Fader Post Fader?
Pre-fader sends. The audio channel signal is sent to the FX channel before the audio channel volume fader. Post-fader sends. The audio channel signal is sent to the FX channel after the audio channel volume fader.
What is a pre-fader used for?
A pre-fader Aux Send taps the incoming signal from the channel at a point that is before the channel fader. So, when the channel fader is down, the signal is still being sent to the aux bus.
Is post EQ pre-fader?
When the Dynamics is set to ‘POST’ then the ‘Post EQ signal tap’ is before the Dynamics section. PreFdr – This tap is before the channel fader. Any channel fader movements will NOT affect the signal coming out of the output taps up to this point.
What is the most common use for a pre-fader aux send?
Pre-fader aux sends are generally used for the monitor mix, because the channel faders don’t affect the signals sent from the aux sends. Any adjustments made to the front-of-the-house mix don’t affect the balance heard by the performers onstage.
What is pre and post EQ?
Each position, EQ pre (before) or EQ post (after) compression produces a distinctly different sound, a different tonal quality, and coloration. As a rule, using EQ in front of your compressor produces a warmer, rounder tone, while using EQ after your compressor produces a cleaner, clearer sound.
Is parallel compression pre or post-fader?
The post-fader setting makes it easier to set your levels, but means your parallel drums will be affected by any level changes to your original drums. … Plus, with pre-fader sends, you can audition the parallel drums even if the original drums are muted. Personally, I tend to go with pre-fader sends.
What is FX send on a mixer?
The FX send controls make it possible to have one effects processor attached to the mixer that all tracks can use. Each track gets a separate control to determine how much, if any, of its audio signal should be sent to the effects processor.
What is pre hear?
This was a form of meeting to determine a substantive point before the main hearing. Pre-hearing reviews were formerly used to strike out the whole or part of a claim or response or to require the payment by a party of a deposit if their case appeared weak.
What is after fader listen?
AFL, which stands for After-Fade Listen, is similar to PFL in function, but takes its signal from a point immediately after the channel fader, showing the level of the channel’s contribution to the mix. … The idea is to allow the monitoring of a channel signal when panned to its appropriate position in the stereo image.
What is post fader listen?
Share. By Sweetwater on Aug 14, 2015, 8:38 AM. Often abbreviated AFL, this refers to overriding the normal monitoring path in a mixer in order to monitor a specific signal after the fader of a channel or group bus, such that the position of the fader will affect the level in the AFL monitor circuit.
What is Pre-fader Metering in Pro Tools?
Pre-Fader Metering: The meter on the channel strip will show the level before the fader, after the inserts, filters and EQ sections. This mode is normally used when recording, so the engineer can “see” at the meter, the level of the signal recorded.
How do you use faders in logic?
Assign keyboard shortcuts for sends on faders
- Choose Logic Pro > Key Commands > Edit.
- Enter “Sends on Fader” into the Key Commands search box.
- Assign keyboard shortcuts for any of these Sends on Faders options: Sends on Fader turns Sends to Faders on or off. Sends on Fader–Next Send selects the next send.
What’s the difference between an AUX and a bus?
Buses group tracks together (allowing for group processing) and auxes affect the duplicate signals of tracks (allowing for parallel processing). If you ever hear someone use the term “return track,” they’re referring to an aux track.
Is parallel compression pre-fader?
Re: Simple parallel compression question
Pre-fader allows you to mix the kick up and down in volume without affecting the way the compressor acts on the bass, so that can help if you’re still in the process of mixing your kick or if you want to automate the kick throughout the track.
What does parallel compression do?
Parallel compression, also known as New York compression, is a dynamic range compression technique used in sound recording and mixing. … Rather than lowering the highest peaks for the purpose of dynamic range reduction, it decreases the dynamic range by raising up the softest sounds, adding audible detail.
What is the difference between pre EQ and post EQ?
The PRE/POST EQ switch does not have a direct effect on your bass sound the way your amp’s standard four band or graphic EQ does. … If you set the switch to PRE, the direct signal is before the amplifier’s equalization section. When set to POST, the direct signal comes after the equalization.
What is a post EQ?
The post EQ switch changes the signal routing in the unit so that after the preamp the signal goes to the EQ first and then the compressor. … If the low end is boosted then the compressor will really squash the signal every time the bass drum sounds, resulting in a ‘pumping’ effect on the cymbals.