Rotating your wheels periodically is a good way to prolong the life of your skateboard and ensure even wear over time. Once you remove the wheels, rotate them in an X pattern. Your left rear wheel becomes your right front wheel, and your right rear wheel becomes your left front wheel.
Why are my skateboard wheels not spinning well?
“New wheels are not going to help in the least if your wheels aren’t spinning. Chances are you just have to clean and lubricate your bearings. … Then soak your bearings in acetone, nail-polish remover or rubbing alcohol. Spin them dry and make sure all the dust and dirt are out.
How do you know if your skateboard wheels are going bad?
The wheels’ diameter slowly decreases over time due to friction and they’ll lose rebound. Hard wheels wear down and develop pitting and tears. Softer wheels usually separate or show tears while the diameter decreases faster.
Why do my skateboard wheels wobble?
CJ: For starters, speed wobs can be caused by a number of different reasons. A common one being loose trucks. Loose trucks can give you too much turning ability, making your set up hyper-responsive for any speed over 10-20mph. If you’re going faster than that, then you just might want to tighten your trucks.
Are skateboards meant to be wobbly?
A wobbly skateboard isn’t a bad thing, some actually like to ride their trucks super loose. Beginners will have a harder time learning to ride a skateboard with loose trucks. After all, a more stable board will help you keep your balance. Just be sure to break bushings in and don’t tighten them until you squish them.
How do I make my skateboard wheels better?
If the wheel comes to a sudden halt and rolls back slightly the other way, it’s too tight. Use the wrench to loosen the nut, but do so only slightly. Just nudge it counter clockwise and spin the wheel again. If it still comes to a quick stop, bump it backwards again.
When should I rotate my skateboard wheels?
Rotating Wheels Regularly
Coning happens when you do power slides or when your skateboarding prefers a certain turn. Eventually, it leads to a smaller riding surface which can impact traction. It’s best to rotate them by using an x pattern.
How long should your bearings spin?
Spinning wheels by hand does not not justify speed, or how fast you will go on a skateboard. Generally, wheels should spin for at least 10 seconds and not stall out. Also, new bearings have a minor break-in period, some quicker than others.
How tight should a skateboard truck be?
Your trucks should be loose enough that you don’t need to tic-tac to get around obstacles while skating around. Skateboard trucks can be set tight or loose, depending on the rider’s preference. That being said, they should be tight enough that the kingpin won’t fall out and loose enough that the bushings don’t burst.
Is it better to have loose or tight trucks?
Tight trucks are better for the ancles, it will prevent future injuries, and if you have one a board with tight trucks will help you to get back sooner than you think. On the other hand, loose trucks won’t make it difficult to line up on an obstacle.
Why is my skateboard turning by itself?
One of the most common causes is cracked or dried bushings. Bushings are the plastic pieces in the center of your trucks. … Depending on the hardness of your bushings the help your trucks to turn smoothly. Over time bushings and pivot cups lose flexibility from steering, weather conditions, and impacts.
Why do I have to push so much on my skateboard?
The first culprit we should look at are the wheels. Bad quality wheels are made way to soft. This causes a certain amount of squishing to the wheels once you stand on the skateboard and put pressure on the wheels.
Do harder skateboard wheels roll faster?
Travel to steeper and smooth roads
On the other hand, if you are using bigger and harder wheels you may surpass these bumps on the rough roads. It is better if you skate on smooth and quite steep roads. Your skateboard will roll fast on these roads, especially if you are using 60mm or 75mm wheels.
What makes a skateboard smooth?
Larger wheels allow you to have a smoother, more comfortable ride. They are also better for riding through different terrain. Smaller wheels are better for tight turns and tricks. Wide skateboard wheels will give you a smoother ride but aren’t conducive for performance riding.
Why are my skateboard wheels so loud?
It could be the hardness of your wheels. The harder they are the more noise they make. When you solely ride asphalt think of replacing your wheels that are a tad softer. It makes all the difference, not to mention a more comfortable ride.
Can I use WD40 on my skateboard bearings?
It’s important to use a silicone-based lubricant. WD40 or others like it will dry out your bearings and attract dust and dirt. … It doesn’t take much, and the excess will just spin out when you replace your shields, pop your bearings back in your wheels and start shredding. Skate safe and enjoy your new-found speed.”
Why is my skateboard so unstable?
The amount they wobble right and left relates to how tight they are. Use a skate tool or other useful tool to tighten or loosen the big nut in the center of the truck. … Turn it clockwise to tighten the trucks, getting tighter turning. Turn it counter-clockwise to loosen the trucks, getting a softer turning feel.
Are Tensor trucks good?
The Tensor Alum Mirror Pink 5.25″ Trucks are an awesome all round truck to get you flipping, grinding and shredding all over the streets and skate parks. A durable truck to stand up to hard riding and tons of grinding.